/* $OpenBSD: sa11x0_reg.h,v 1.3 2008/06/26 05:42:09 ray Exp $ */ /* $NetBSD: sa11x0_reg.h,v 1.4 2002/07/19 18:26:56 ichiro Exp $ */ /*- * Copyright (c) 2001 The NetBSD Foundation, Inc. All rights reserved. * * This code is derived from software contributed to The NetBSD Foundation * by IWAMOTO Toshihiro. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. */ #ifndef _ARM_SA11X0_REG_H_ #define _ARM_SA11X0_REG_H_ /* Physical register base addresses */ #define SAOST_BASE 0x90000000 /* OS Timer */ #define SARTC_BASE 0x90010000 /* Real-Time Clock */ #define SAPMR_BASE 0x90020000 /* Power Manager */ #define SARCR_BASE 0x90030000 /* Reset Controller */ #define SAGPIO_BASE 0x90040000 /* GPIO */ #define SAIPIC_BASE 0x90050000 /* Interrupt Controller */ #define SAPPC_BASE 0x90060000 /* Peripheral Pin Controller */ #define SAUDC_BASE 0x80000000 /* USB Device Controller*/ #define SACOM1_BASE 0x80010000 /* GPCLK/UART 1 */ #define SACOM3_HW_BASE 0x80050000 /* UART 3 */ #define SAMCP_BASE 0x80060000 /* MCP Controller */ #define SASSP_BASE 0x80070000 /* Synchronous serial port */ #define SADMAC_BASE 0xB0000000 /* DMA Controller */ #define SALCD_BASE 0xB0100000 /* LCD */ /* Register base virtual addresses mapped by initarm() */ #define SACOM3_BASE 0xd000d000 /* Interrupt controller registers */ #define SAIPIC_NPORTS 9 #define SAIPIC_IP 0x00 /* IRQ pending register */ #define SAIPIC_MR 0x04 /* Mask register */ #define SAIPIC_LR 0x08 /* Level register */ #define SAIPIC_FP 0x10 /* FIQ pending register */ #define SAIPIC_PR 0x20 /* Pending register */ #define SAIPIC_CR 0x0C /* Control register */ /* width of interrupt controller */ #define ICU_LEN 32 /* Reset controller registers */ #define SARCR_RSRR 0x0 /* Software reset register */ #define SARCR_RCSR 0x4 /* Reset status register */ #define SARCR_TUCR 0x8 /* Test Unit control reg */ #endif /* _ARM_SA11X0_REG_H_ */